Application
Classification
E600 120 (ved hod i↔o) S 1500 Cmod AA Single
Nominal sizes
Parts and characteristics
Attachments
Optional products
TROXNETCOM
TROX-X FANS smoke exhaust fans from the X-FANS subassembly
All smoke exhaust fans are tested to EN 12101-3, for F200/F300/F400 and F600, depending on the type. With CE marking, declaration of performance and application approval for the German market. Speed adjustment for smoke exhaust fans
Construction features
Materials and surfaces
Standards and guidelines
Maintenance
Smoke control dampers must be operational at all times and must be maintained regularly so that they meet the performance requirements.
1 Casing
2 Linkage cover (cut open)
3 Drive linkage
4 Actuator
5 Rating plate
6 Side seal
7 Damper blades
8 Damper blade profiled seal
Type EK-JS smoke control dampers are tested according to EN12101-8 and EN 1366-10. In rectangular steel and stainless steel construction. Intended for the discharge of smoke and heat in smoke extract systems and for the flow of necessary supply air into the area from which smoke is to be extracted. EK-JS is intended for use in pressurised ventilation systems (DBA) in order to keep safety stairwells and their anterooms and fire brigade lift shafts or escape tunnels smoke-free. They thus enable the controlled discharge of released smoke. EK-JS is intended for use in single sections and may be used at elevated operating temperatures of up to 600 °C on and in horizontally and vertically aligned smoke extract ducts according to EN 12101-7, tested according to EN 1366-9. EK-JS can be used in combined systems (combination damper) for ventilation and is suitable for restricting extract air volume flows. The OPEN-CLOSE actuators can be signalled either with ready-wired actuator control modules or with bus modules.
Nominal sizes B × H | 100 × 100 – 1250 × 2560 mm |
Casing length | 200 mm |
Volume flow rate range at 10 m/s | From 360 m³/h to 115110 m³/h or |
Differential pressure range | Pressure level 3: -1500 to 500 Pa |
Operating temperature | 30 °C – 50 °C without temperatures below the dew point |
Upstream velocity with same upstream and downstream flow |
|
Closed damper blade air leakage | EN 1751, at least class 2, |
Casing leakage | EN 1751, class B, from nominal width 840 × 480 class C |
EC conformity |
|
Declaration of performance | DoP/EK-JS/001 |
Correction for different throttle positions
The adjustment of the damper blade angle enables the setting of different throttle positions.
Based on the determined data for the open position, both the resistance coefficient and the sound power level can be corrected to design the operating conditions with angled blades.
For this purpose, the resistance coefficient is multiplied by the correction factor C, which corresponds to the diagram of the "Resistance factor"
for the correction factor.
For the correction of the sound power level, this is added to the correction value K, which corresponds to the diagram of the "Sound power level"
for the correction value.
Smoke control dampers with a height of less than or greater than 320 mm are differentiated.
Example:
EK-JS / installation case A
H × B: 960 mm × 1000 mm
Upstream velocity: 5 m/s
EPF (data for OPEN position)
Correction for a blade angle of 65
(read from diagram correction factor "resistance coefficient" and correction value "sound power level")
Resistance factor:
Correction value C = 20
0.23 × 20 = 4.6
Sound power level:
Correction value K = 8
40 dB(A) + 8 dB(A) = 48 dB(A)
Type EK-JS smoke control dampers are tested according to EN12101-8 and EN 1366-10. In rectangular steel and stainless steel construction. Intended for the discharge of smoke and heat in smoke extract systems and for the flow of necessary supply air into the area from which smoke is to be extracted. EK-JS is intended for use in pressurised ventilation systems (DBA) in order to keep safety stairwells and their anterooms and fire brigade lift shafts or escape tunnels smoke-free. They thus enable the controlled discharge of released smoke. EK-JS is intended for use in single sections and may be used at elevated operating temperatures of up to 600 °C on and in horizontally and vertically aligned smoke extract ducts according to EN 12101-7, tested according to EN 1366-9. EK-JS can be used in combined systems (combination damper) for ventilation and is suitable for restricting extract air volume flows. The OPEN-CLOSE actuators can be signalled either with ready-wired actuator control modules or with bus modules.
Materials and surfaces
Technical data
Exemplary for a nominal smoke control damper width of 1250 × 960 related to the mean airflow velocities v = 5 m/s
∆Pt = 3.5 Pa
dB(A) = 40
Afree = 1.095 m²
Ageo = 1.2 m²
qv = 21600 m³/h
Standards and guidelines
Classification
E600 120 (ved hod i↔o) S 1500 Cmod AA Single
Nominal sizes
Dimensions B × H: 100 × 100 – 1250 × 2560 [mm]
Casing length L = 200 mm
Accessories
Attachments
Equivalence criteria
EK-JS | – | 2 | / | DE | / | 600 × 800 | / | 17 | / | K0 | / | B24A | / | P1 – RAL... | / | P2 – RAL... |
| | | | | | | | | | | | | | | | | | ||||||||
1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 | 9 |
2 Stainless steel
3 Country of destination
DE Germany
CH Switzerland
AT Austria
PL Poland
and others
5 Accessories
No entry required: None (standard)
17 HT sealing tape (15 mm)
18 Suspension brackets for horizontal damper alignment
19 Suspension brackets for horizontal damper alignment and HT sealing tape (15 mm)
7 Attachments
224 V AC/DC:
B24 (Actuator)
B24SR (Actuator continuous control, ventilation function Cmod1) 24 V AC/DC: with operating range DC 2 – 10 V230 V AC:
B230 (Actuator)
Actuator combined with TROX control module:Module for signalling, TROXNETCOM:No entry required: None (standard)
P1 Powder-coated RAL 7030 (technical lacquer paint finish), industrial polyester
80% ±5 gloss levels, texture grade: texturedor all other colours according to RAL chart, gloss level
80% ± 5 gloss levels, texture grade: smooth
9 Surface of attachment 1
No entry required: None (standard)
P2 Powder-coated RAL 7030 (technical lacquer paint finish), industrial polyester
80% ±5 gloss levels, texture grade: texturedor all other colours according to RAL chart, gloss level
80% ± 5 gloss levels, texture grade: smooth
Type | EK-JS |
Construction | Galvanised steel standard construction |
Country of destination | Germany |
Nominal size | 600 × 800 |
Accessories | HT sealing tape |
Attachment 1 | Expanded metal mesh on the operating side |
Attachment 2 | Actuator with TROXNETCOM control module AS-EM/EK |
Standard construction of surface | P1 RAL 9010 80%: Smoke control damper with powder coating, RAL 9010, pure white, gloss level 80%, texture grade: smooth |
Surface of attachment 1 | None (standard) |
⓵ Keep area free for accessibility of the actuator
② Fixing option for control module
H | B | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
100 | 150 | 200 | 250 | 300 | 350 | 400 | 450 | 500 | 550 | 600 | 650 | |
100 | 7.33 | 7.65 | 8.02 | 8.33 | 8.65 | 8.97 | 9.28 | 9.6 | 9.92 | 10.23 | 10.55 | 10.87 |
125 | 7.58 | 7.9 | 8.27 | 8.59 | 8.9 | 9.22 | 9.54 | 9.86 | 10.18 | 10.5 | 10.82 | 11.14 |
150 | 7.82 | 8.15 | 8.52 | 8.84 | 9.16 | 9.48 | 9.8 | 10.13 | 10.45 | 10.77 | 11.09 | 11.41 |
165 | 8.07 | 8.39 | 8.77 | 9.09 | 9.42 | 9.74 | 10.06 | 10.39 | 10.71 | 11.04 | 11.36 | 11.69 |
320 | 11.29 | 11.95 | 12.62 | 13.29 | 13.95 | 14.62 | 15.28 | 15.95 | 16.62 | 17.29 | ||
480 | 13.41 | 14.17 | 14.92 | 15.68 | 16.44 | 17.2 | 17.95 | 18.71 | 19.47 | 20.22 | ||
640 | 15.54 | 16.38 | 17.23 | 18.08 | 18.92 | 19.77 | 20.62 | 21.47 | 22.31 | 23.16 | ||
800 | 17.66 | 18.6 | 19.53 | 20.47 | 21.41 | 22.35 | 23.28 | 24.22 | 25.16 | 26.1 | ||
960 | 19.78 | 20.81 | 21.84 | 22.87 | 23.9 | 24.92 | 25.95 | 26.98 | 28.01 | 29.04 | ||
1120 | 21.96 | 23.1 | 24.23 | 25.37 | 26.51 | 27.64 | 28.78 | 29.92 | 31.05 | 32.19 | ||
1280 | 24.14 | 25.38 | 26.63 | 27.87 | 29.12 | 30.36 | 31.61 | 32.85 | 34.1 | 35.35 | ||
1440 | 26.31 | 27.67 | 29.02 | 30.37 | 31.73 | 33.08 | 34.43 | 35.79 | 37.15 | 38.72 | ||
1600 | 28.49 | 29.95 | 31.41 | 32.88 | 34.34 | 35.8 | 37.48 | 38.95 | 40.41 | 41.88 | ||
1760 | 30.66 | 32.24 | 33.81 | 35.38 | 37.17 | 38.74 | 40.31 | 41.88 | 43.46 | 45.03 | ||
1920 | 32.84 | 34.52 | 36.42 | 38.1 | 39.78 | 41.46 | 43.14 | 44.82 | 46.5 | 48.19 | ||
2080 | 35.02 | 37.03 | 38.81 | 40.6 | 42.39 | 44.18 | 45.97 | 47.76 | 49.55 | 51.34 | ||
2240 | 37.41 | 39.31 | 41.21 | 43.1 | 45 | 46.9 | 48.8 | 50.7 | 52.6 | 54.5 | ||
2400 | 39.59 | 41.6 | 43.6 | 45.61 | 47.62 | 49.62 | 51.63 | 53.63 | 55.64 | 59.25 | ||
2560 | 41.76 | 43.88 | 45.99 | 48.11 | 50.23 | 52.34 | 54.45 | 56.57 | 60.29 | 62.41 |
H | B | |||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|
700 | 750 | 800 | 850 | 900 | 950 | 1000 | 1050 | 1100 | 1150 | 1200 | 1250 | |
100 | 11.18 | 11.5 | 11.82 | 12.13 | 12.45 | 12.77 | 13.08 | 13.4 | 13.72 | 14.03 | 14.35 | 14.67 |
125 | 11.46 | 11.78 | 12.1 | 12.42 | 12.73 | 13.05 | 13.37 | 13.69 | 14.01 | 14.33 | 14.65 | 14.97 |
150 | 11.73 | 12.06 | 12.38 | 12.7 | 13.02 | 13.34 | 13.66 | 13.99 | 14.31 | 14.63 | 14.95 | 15.27 |
165 | 12.01 | 12.33 | 12.66 | 12.98 | 13.31 | 13.63 | 13.95 | 14.28 | 14.6 | 14.93 | 15.25 | 15.58 |
320 | 17.95 | 18.62 | 19.28 | 19.95 | 20.62 | 21.28 | 21.95 | 22.62 | 23.28 | 23.95 | 24.62 | 25.29 |
480 | 20.98 | 21.74 | 22.49 | 23.25 | 24.01 | 24.76 | 25.52 | 26.28 | 27.03 | 27.79 | 28.55 | 29.31 |
640 | 24.01 | 24.85 | 25.7 | 26.55 | 27.39 | 28.24 | 29.09 | 29.94 | 30.78 | 31.63 | 32.48 | 33.33 |
800 | 27.03 | 27.97 | 28.91 | 29.85 | 30.78 | 31.72 | 32.66 | 33.6 | 34.53 | 35.47 | 36.41 | 37.35 |
960 | 30.06 | 31.09 | 32.12 | 33.15 | 34.17 | 35.2 | 36.23 | 37.26 | 38.28 | 39.31 | 40.34 | 41.59 |
1120 | 33.32 | 34.46 | 35.6 | 36.74 | 37.87 | 39.01 | 40.37 | 41.5 | 42.64 | 43.77 | 44.91 | 46.11 |
1280 | 36.59 | 37.83 | 39.3 | 40.55 | 41.79 | 43.04 | 44.28 | 45.53 | 46.77 | 48.02 | 49.26 | 50.51 |
1440 | 40.07 | 41.43 | 42.78 | 44.14 | 45.49 | 46.84 | 48.2 | 49.55 | 50.9 | 52.26 | 53.62 | 55.03 |
1600 | 43.34 | 44.8 | 46.26 | 47.73 | 49.19 | 50.65 | 52.12 | 53.58 | 55.04 | 56.5 | 57.97 | 59.43 |
1760 | 46.6 | 48.17 | 49.74 | 51.32 | 52.89 | 54.46 | 56.03 | 57.61 | 59.17 | 62.35 | 63.92 | 65.55 |
1920 | 49.86 | 51.55 | 53.23 | 54.91 | 56.58 | 58.27 | 61.55 | 63.23 | 64.91 | 66.59 | 68.27 | 69.95 |
2080 | 53.13 | 54.92 | 56.71 | 58.5 | 61.88 | 63.68 | 65.47 | 67.26 | 69.04 | 70.83 | 72.62 | 74.47 |
2240 | 56.39 | 59.89 | 61.79 | 63.69 | 65.58 | 67.48 | 69.38 | 71.28 | 73.18 | 75.08 | 76.98 | 78.88 |
2400 | 61.25 | 63.26 | 65.27 | 67.28 | 69.28 | 71.29 | 73.3 | 75.31 | 77.31 | 79.32 | 81.33 | 83.4 |
2560 | 64.52 | 66.64 | 68.75 | 70.87 | 72.98 | 75.1 | 77.22 | 79.33 | 81.44 | 83.56 | 85.68 | 87.8 |
Application
Variants
B24
B230
B24-SR
The torque required to operate the smoke control damper depends on the size, which is why the actuator type cannot be chosen freely.
Torque tables
Actuator | BEN24-ST | BEE24-ST | BE24-ST |
Supply voltage (AC) | AC 19.2 – 28.8 V, 50/60 Hz | ||
Supply voltage (DC) | DC 21.6 – 28.8 V, 50/60 Hz | ||
Power consumption – when running | 3 W | 2.5 W | 12 W |
Power consumption – when idle | 0.1 W | 0.5 W | |
Power rating for cable sizing | Imax. 8.2 A at 5 ms | ||
Torque | 15 Nm | 25 Nm | 40 Nm |
Run time for 90° | < 30 s | ||
Limit switch contacts | 2 × EPU | ||
Switching current | 1 mA – 3 A (0.5 A inductive), AC 250 V | 1 mA – 6 A (0.5 A inductive), AC 250 V | |
Limit switch – open | 5° | 3° | |
Limit switch – close | 80° | 87° | |
Connecting cable – actuator | Cable 1 m, 3 × 0.75 mm², halogen-free | ||
Connecting cable – limit switches | Cable 1 m, 6 × 0.75 mm², halogen-free | ||
IEC protection class | III safety extra low voltage (SELV) | ||
Protection level | IP 54 | ||
EC conformity | CE according to 2014/30/EU Low Voltage Directive CE according to 2014/35/EU | ||
Operating temperature | -30 to 55 °C | ||
Weight | 0.9 kg | 1.1 kg | 2.7 kg |
Actuator | BEN230 TR | BEE230 TR | BE230 TR |
Supply voltage (AC) | AC 198 – 264 V, 50/60 Hz | ||
Power consumption – when running | 4 W | 3.5 W | 8 W |
Power consumption – when idle | 0.4 W | 0.5 W | |
Power rating for cable sizing | Imax. 4 A at 5 ms | Imax. 7.9 A at 5 ms | |
Torque | 15 Nm | 25 Nm | 40 Nm |
Run time for 90° | < 30 s | ||
Limit switch contacts | 2 × EPU | ||
Switching current | 1 mA – 3 A (0.5 A inductive), AC 250 V | 1 mA – 6 A (0.5 A inductive), AC 250 V | |
Limit switch – open | 5° | 3° | |
Limit switch – close | 80° | 87° | |
Connecting cable – actuator | Cable 1 m, 3 × 0.75 mm², halogen-free | ||
Connecting cable – limit switches | Cable 1 m, 6 × 0.75 mm², halogen-free | ||
IEC protection class | II reinforced insulation | ||
Protection level | IP 54 | ||
EC conformity | CE according to 2014/30/EU Low Voltage Directive CE according to 2014/35/EU | ||
Operating temperature | -30 to 55 °C | -30 to 50 °C | |
Weight | 0.9 kg | 1.1 kg | 2.7 kg |
Actuator | BEN24-SR | BEE24-SR |
Supply voltage (AC) | AC 19.2 – 28.8 V, 50/60 Hz | |
Supply voltage (DC) | DC 21.6 – 28.8 V, 50/60 Hz | |
Power consumption – when running | 3 W | |
Power consumption – when idle | 0.3 W | |
Power rating for cable sizing | Imax. 8.2 A at 5 ms | |
Torque | 15 Nm | 25 Nm |
Run time for 90° | < 30 s | |
Limit switch contacts | 2 × EPU | |
Switching current | 1 mA – 3 A (0.5 A inductive), AC 250 V | |
Limit switch – open | 5° | |
Limit switch – close | 80° | |
Connecting cable – actuator | Cable 1 m, 4 × 0.75 mm², halogen-free | |
Connecting cable – limit switches | Cable 1 m, 6 × 0.75 mm², halogen-free | |
IEC protection class | III safety extra low voltage (SELV) | |
Protection level | IP 54 | |
EC conformity | CE according to 2014/30/EU Low Voltage Directive CE according to 2014/35/EU | |
Operating temperature | -30 to 55 °C | |
Weight | 1.1 kg | 0.9 kg |
Interfaces to higher level systems
TROX fire and smoke protection systems have standardised interfaces for central building management systems. In the simplest case, the interface consists of discrete signalling contacts that connect the alternating inputs and outputs of TROX systems and other building components.
Control and communication modules for smoke control dampers
Type | B24A | B24AS | B24BKNE | B24C | B230D | B24D | B24AM |
---|---|---|---|---|---|---|---|
AS-EM/EK | AS-EM/SIL2 | BKNE230-24 | BC24-G2 | BRM-10-F | BRM-10-F-ST | AS-EM/M | |
EK-EU | × | × | × | × | × | × | × |
EK-JZ | × | × | × | × | × | × | × |
EK-JS | × | × | × | × | × | × | × |
Note:
Actuators and communication modules are factory tested together; only tested combinations must be used.
B24A – AS-EM/EK
Application
Use
B24A – Mounted to the smoke control damper
Description | AS-EM/EK |
Electrical design | 4 inputs/3 outputs |
Output function | PNP transistor |
Supply voltage | 26.5 – 31.6 V DC |
Current consumption, including actuator | 450 mA |
Inputs: | |
Switching | DC PNP |
Sensor voltage supply | AS-i |
Voltage range | 18 – 30 V AC |
With short circuit protection | Yes |
Switching level – high signal 1 | 10 |
Input current high/low | > 7 mA/< 2 mA |
Input characteristic | IEC 61131-2 Type 2 |
Outputs, PNP: | |
Galvanically isolated | No |
Max. current load per output | 400 mA per output/400 in total (from AS-i) |
Outputs, relay: | |
Galvanically isolated | Yes |
Maximum voltage | 32 V |
Max. current load | 500 mA |
Ambient temperature | -5 to 75 °C |
Protection level, IEC protection class | IP 42 |
AS-i profile | S-7.A.E |
I/O configuration | 7 Hex |
ID code | 7 Hex |
EMC | EN 61000-6-2; EN 61000-6-3 |
Application
Use
B24AS – Mounted to the smoke control damper
Description | AS-EM/SIL2 |
Supply voltage | 26.5 – 31.6 V DC |
Current consumption | < 400 mA from AS-i |
Max. current load per output | 340 mA |
Max. current load per module | 340 mA |
Status LED | |
AS-i power | 1 × green |
PeripheralFault | 1 × red, blinking |
ComError | 1 × red, static |
Output Q0 | 1 × yellow (DO0) |
Output Q1 | 1 × yellow (DO1) |
Input status LED SI-1 | 1 × yellow |
Input status LED SI-2 | 1 × yellow |
Input status DI0 | 1 × yellow (DI0) |
Input status DI1 | 1 × yellow (DI1) |
Input status DI2 | 1 × yellow (DI2) |
Binary inputs | 2 outputs with transistor (typically 24 V DC from AS-i, voltage range 18 – 30 V) |
Operating temperature | -20 to 70 °C |
Storage temperature | -20 to 75 °C |
Protection level, IEC protection class | IP 54 |
Casing material | Plastic |
AS-i profile | S-7.B.E (Safety at Work) and S7.A.E (motor module) |
EMC | EN 61000-6-2; EN 61000-6-3 |
B24AM – AS-EM/M
Application
Use
B24AM – Mounted to the smoke control damper
Description | AS-EM/M |
Electrical design | 4 inputs/3 outputs |
Output function | PNP transistor |
Supply voltage | 26.5 – 31.6 V DC |
Current consumption, including actuator | 450 mA |
Inputs | |
Switching | DC PNP |
Sensor voltage supply | AS-i |
Voltage range | 18 – 30 V AC |
With short circuit protection | Yes |
Switching level – high signal 1 | 10 |
Input current high/low | > 7 mA/< 2 mA |
Input characteristic | IEC 61131-2 Type 2 |
Outputs, PNP | |
Galvanically isolated | No |
Max. current load per output | 400 mA per output/400 in total (from AS-i) |
Outputs, relay | |
Galvanically isolated | Yes |
Maximum voltage | 32 V |
Max. current load | 500 mA |
Ambient temperature | -5 to 75 °C |
Protection level, IEC protection class | IP 42 |
AS-i profile | S-7.A.E |
I/O configuration | 7 Hex |
ID code | 7 Hex |
EMC | EN 61000-6-2; EN 61000-6-3 |
B24BKNE – Communication module
Application
Use
B24BKNE – BKNE230-24 communication module
Description | BKNE230-24 |
Nominal voltage | 230 V AC 50/60 Hz |
Functional range | 198 – 264 V AC |
Rating | 19 VA (including actuator) |
Power consumption | 10 W (including actuator) |
Length / cross section | On the actuator = 1 m, 3 (6*) × 0.75 mm² (free of halogens) |
IEC protection class | II (protective insulation) |
Ambient temperature | -30 to 50 °C |
Storage temperature | -40 to 80 °C |
Protection level | IP 54 |
EC conformity | EMC to 89/336/EEC, 73/23/EEC |
Mode of action | Type 1 (EN60730-1) |
Software class | A (EN60730-1) |
Maintenance | Maintenance-free |
Weight | 680 g |
B24C – Communication module
Application
Use
B24C – BC24-G2 communication module from BV-Control AG
Description | B24C |
Nominal voltage | From SLC® control module |
Power consumption | 1 W |
Connections | Plug connections, screw terminals |
Damper power supply | 24 V |
Ambient temperature | -20 to 50 °C |
Storage temperature | -20 to 80 °C |
Humidity | 95 % rh, no condensation |
Weight | 255 g |
B × H × T | 114 × 153 × 54 mm |
Max. impulse voltage | 2.5 kV (EN60730-1) |
B24D, B230D – Communication module
Application
Use
B24D – AGNOSYS BRM10FST communication module
B230D – AGNOSYS BRM10F communication module
Description | B24D/B230D |
Nominal voltage | 18 – 32 V DC (typically 24 V) |
Connections | Plug connections, screw terminals |
Damper power supply | 24/230 V AC 24 V DC |
Ambient temperature | 0 to 45 °C |
Humidity | 90 % rh, no condensation |
Weight | 510 g |
B × H × T | 158 × 180 × 65 mm |
Share page
Recommend this page
Recommend this page by sending a link by mail.
Share page
Thank you for your recommendation!
Your recommendation has been sent and should arrive shortly.
Contact
We are here for you
Please specify your message and type of request
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265
Contact
Thank you for your message!
Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265
Contact
We are here for you
Please specify your message and type of request
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265
Contact
Thank you for your message!
Your message is send and will be processed shortly.
Our department for Service-Requests will contact you asap.
For general question regarding products or services you can also call:
Tel.: +49 (0)2845 / 202-0 | Fax: +49 (0)2845/202-265